PTO in new tractor

•Multi-plate dry clutch – Electro-hydraulically actuated mechanically engaged multi-plate dry clutch takes drive straight from the crankshaft pulley. The 1000 rpm PTO is either “on” or “off” there is no modulation.

1. PTO multi-plate dry clutch

2. PTO control housing

3. PTO input shaft

4. Engine crankshaft pulley coupler

5. PTO reduction gearbox

•

•Self Lubrication Gearbox – Fully self contained system, Multiplate clutch electro-hydraulically engaged via a proportional solenoid valve allowing a modulated starting of the 1000 rpm PTO. The PTO is either “on” or “off” there is no modulation. Drive supplied from the engine crankshaft through duplex chain drive and sprockets.

1. Input from engine crankshaft via Duplex chain & sprockets

2. Piston Brake

3. Lubrication & return oil pumps

4. Output shaft 1000 rpm (Clockwise from seat)

5. Oil return to transmission sump

6. Oil supply (from tractor Low Pressure circuit)

7. Control Solenoid

•

•Zuidberg - DIA Kits are available for many products which incorporate smooth PTO start-up with electro-hydraulic proportional valve.

1.Friction discs and steel plates

2.Clutch release bearing

3.Spring

4.Piston

5.Diaphragm spring

•

Disengaged

•Solenoid valve de-energised allowing the oil to return to the reservoir.

•The spring (3) pushes the piston (4) out of the housing and pushes the clutch release bearing (2) into the PTO clutch diaphragm spring (5).

•Pressure is applied to the diaphragm spring (5)  releasing the force acting on the clutch pressure plate.

•The springs in between the friction discs and steel plates (1) expand, allowing the clutch hub to rotate freely within the clutch housing.

Engaged

•Solenoid valve is energised, applying low pressure oil to the piston (4).

•Low pressure oil acting against the piston (4), overcomes the piston spring (3), retracting the piston (4) into the housing, releasing the clutch release bearing (2) from the force of the diaphragm spring (5).

• The diaphragm spring (5), compresses the springs in between the friction discs and steel plates (1), clamping the friction discs and steel plates (1) together, locking the clutch hub and the clutch housing together.

Oil pressure and return for front PTO via Front brake valve.

1 - Oil return pipe

2 - Oil pressure supply pipe

NOTE: This block must be fitted when the Front PTO option is requested, even if the tractor has not got front brakes.

to be continue 

Supersteer in new tractor

As the hubs on the axle turn up to 45º, the axle simultaneously 

articulates up to 20º

giving a total turn angle of 65º. This means the operator can 

 turn tighter and

more quickly at the end of the field.

This results in smaller headlands leading to Less compaction 

and greater productivity.

The SuperSteer system ulitises two large diameter steering rams 

 and two tie rods

which connect the axle hub to the tractor chassis. As the steering ram extends, the tie rod linking the front axle to  the tractor

causes the axle to progressively articulate in the direction of wheel turn.

SuperSteer Axle Components

1. Steering Cylinder

2. Pin

3. Tie Rod

4. Pin

5. Bushing

6. Spacer

7. Support

8. Tube

9. Bushing

10. Support

11. Ring Nut

12. Bushing

13. Support

14. Axle

15. Bracket

16. Retaining Ring

صورة من العمل لألة رفع بالات البرسيم البيكر فى شرق العوينات مصر

A photo of the work to Lifted from the 

ground bales of alfalfa

Electronic Draft Control EDC in tractor

• Controlled by processor ( 9 )

• Inputs from:

•Operator

• EDC control pod ( 8 )

• EDC control panel ( 2 )

• Linkage

• Lift arm potentiometer ( 7 )

• Load sensing pins ( 6 )

• Radar ( for slip control only ) ( 1 )

• Outputs

• EDC valve ( 4 ) - controls CCLS pump via sensing lines and diverts pressure oil to lift cylinders.

• Instrument cluster ( 3 ) - displays linkage height, slip %  and EDC errors.

•

• Controls position of implement and / or regulates draft force on tractor by raising / lowering implement into / out of work

Video P.t.o tractor newholland tm 7040 فيديو فك مجموعة عمود الإدارة الخلفى

Steering Circuit Pressure Test in tractor

Checks for any steering circuit internal leaks

Pressure reading less than 186 bar at full lock possible steering relief valve set incorrectly or an internal leak

Carry out steering relief valve pressure test to eliminate cause of leak

Hydraulic Pump

1.Trailer brake valve

2.Low pressure regulating valve

3.Suspension levelling valves

4.High pressure piston pump

5.Suction filter blocked switch

5a.  Charge pressure low switch

6.Pressure & flow compensating valve

7.Steering priority valve

8.Steering pressure gear pump

9.Lube makeup valve

10.Suction Filter

11.Start-up temperature switch

12.Charge pressure filter

13.Charge pressure rotary pump

Brakes POWERTRAINS

Brakes POWERTRAINS

•Types of Brakes  أنواع الفرامل

•Caliper كوبلن 

•Ball and Ramp

•Piston and Disc بستم وقرص دسك 

braking circuit  دائرة الفرامل عامة

1.Master cylinders x 2                                                                       الأسطوانة الرئيسية

2. Air brake control valve                                                          صمام التحكم فىهواء الفرامل

3.Trailer brake valve                                                                         صمام كابح مقطورة                     

4.Trailer brake valve coupler                                                   صمام كابح مقطورة مقترن

5.Rear service brakes                                                                    فرامل الخدمة الخلفية

6.Hand brake components                                             مكونات فرامل اليد تكون على الجهاز الفرقى

7.Front axle                                                                                   المحور الأمامى

8.Front brake system booster valve / master cylinder     صمام نظام الفرامل الأمامية رئيسى

• Reservoir oil - blue                                               لون أزرق   زيت الفرامل الراجع

• Main brake circuit oil - brown                                 لون بنى مسار سريان زيت الفرامل الرئيسى أو الضاغط

• Front brake “boosted” circuit - Purple                   

• Low pressure hydraulic system oil - orange

• Oil to hydraulic trailer brake coupler - yellow

•

• The diagram shows the closed centre brake circuit - Both brake pedals must be depressed to operate front axle and air brakes. 

• If open centre hydraulic pump, there is only one brake line ( right side ) to trailer brake valve - The front axle and air brakes will be operated when the right hand brake pedal is depressed.

Brakes POWERTRAINS

•Types of Brakes  أنواع الفرامل

•Caliper كوبلن 

•Ball and Ramp

•Piston and Disc بستم وقرص دسك 

braking circuit  دائرة الفرامل عامة

1.Master cylinders x 2                                                                       الأسطوانة الرئيسية

2. Air brake control valve                                                          صمام التحكم فىهواء الفرامل

3.Trailer brake valve                                                                         صمام كابح مقطورة                     

4.Trailer brake valve coupler                                                   صمام كابح مقطورة مقترن

5.Rear service brakes                                                                    فرامل الخدمة الخلفية

6.Hand brake components                                             مكونات فرامل اليد تكون على الجهاز الفرقى

7.Front axle                                                                                   المحور الأمامى

8.Front brake system booster valve / master cylinder     صمام نظام الفرامل الأمامية رئيسى

• Reservoir oil - blue                                               لون أزرق   زيت الفرامل الراجع

• Main brake circuit oil - brown                                 لون بنى مسار سريان زيت الفرامل الرئيسى أو الضاغط

• Front brake “boosted” circuit - Purple                   

• Low pressure hydraulic system oil - orange

• Oil to hydraulic trailer brake coupler - yellow

•

• The diagram shows the closed centre brake circuit - Both brake pedals must be depressed to operate front axle and air brakes. 

• If open centre hydraulic pump, there is only one brake line ( right side ) to trailer brake valve - The front axle and air brakes will be operated when the right hand brake pedal is depressed.

live stock تمسين الماشية

We will explain the feasibility study for the project fattening cattle from the beginning of construction of the farm to establish the same building from the ground up to the ceiling

Then the manger, canals and farm design from the inside to facilitate work

Then talk about the rooms and feed barley cultivar

The purchase of livestock, marketing and diseases

And the economic situation of the farm
The machines use

And cultivated infant feed for fattening farm service

This is a picture of the farm but are characterized by primitive mud brick walls a best thermally winter and summer

سوف نقوم بشرح دراسة جدوى لمشروع تسمين ماشية من بداية البناء للمزرعة من تأسيس المبنى نفسه من الأساس حتى السقف 

ثم المعلف والمساقى وتصميم المزرعة من الداخل لتسهيل العمل 
ثم الحديث عن الأعلاف وغرف الشعير المستنبت 
وشراء الماشية وتسويقها والأمراض 
والوضع الإقتصادى للمزرعة
والألات المستخدمة 

والأرض المزروعة أعلاف لخدمة مزرعة التسمين

جيربوكس عمود الإدارة الخلفى وإصلاح عطل بجرار كلاس 260حصان class tractor 260 hp - Gearbox power take off(p.t.o) and fix the malfunction

جرار كلاس 260 حصان 

class tractor 260 hp

Topics or posts linked or related

مواضيع أو مشاركات مرتبطة أو ذات صلة

http://ebraheemseleman.blogspot.com/p/videos.html

http://ebraheemseleman.blogspot.com/p/blog-page_4.html

Adjustment of the knotter in big baler part4 5. Adjustments

Do not adjust the baler without having seen the performance in the field
Only adjust if really necessary or after maintenance/renewal 

A.Twine quality

Take a half of meter twine and start untwisting the twine.
A good quality twine will have 15 to 30 windings, a bad quality twine 8 or less.

Q-twine is produced by Cotesi S.A., europe’s largest and most advanced twine producer
They are ISI 9000 accredited.

Ferric-oxide colour (rust colour) offers enhanced U.V. protection and is long lasting when exposed to sunlight.

Q-TWINE has ‘Easy-Feed’ spools to ensure trouble-free knotting from the start

B.Twine tension

Practical adjustment :

-Completely loosen the twine tensioners.

-Pull the twine (in the bale chamber or after the tucker arm) towards you.

-Increase twine tension until the slacker arm comes down and stays down without pulling twine from the twineboxes.

During the formation of a bale the slacker arm (and indicator flags) are in the completely down position. If it raises, increase twine tension

C.Knotter Bill hook

Practical adjustment :

-Untighten the billhook spring nut until the bill hook opens.

-Hold the billhook tongue open with your finger.

-Tighten the nut until the billhook tongue just closes. Do not overtighten.

D.Stripper arm

Practical adjustment :

-A force of 40 to 60 N should be necessary to move the stripper arm flange over the heel of the bill hook.

-When adjusted correctly, the notch of the stripper arm will travel beyond the end of the bill hook with a minimum distance X = 15 mm

-Adjusting : bending

small adjustments : on stack.

Larger adjustments : dismount

E.Twine disc

Engineering adjustment :

X = 2 – 3 mm

Practical adjustment :

Twine must be in the middle of the opened billhook.

F.Twine holder

Adjust until pigtail length is +/- 15 mm. Adjust ¼ of a turn each time.

Indication to start : empty twine disc, first tighten the springs by hand, then add 8 flats of a bolt 

(8 x 60 °)